height=23
Catalogue
All prices upon enquiry!
 Art.-Nr.: 124
Casing for toothed ventilation BKT
 Art.-Nr.: 125
Casing for toothed ventilation DGT toothed bar LV20K
 Art.-Nr.: 126
Casing for toothed ventilation bar, cross toothed bar
 Art.-Nr.: 127
Casing for toothed ventilation, lock toothed bar
 Art.-Nr.: 128
Casing for toothed ventilation bar/shading bar for steel cross toothed bar, size 30
 Art.-Nr.: 129
Casing for toothed shading bar for steel cross toothed bar, size 40
 Art.-Nr.: 131
Toothed bars
All toothed bars (straight and/or bowed) are available in various sizes. Please inquire desired toothed bars seperatley.
 Art.-Nr.: 4
Manual cable winch
For manual operation of shading systems up to approx. 180 m2.
 Art.-Nr.: 13
Ball bearing 50x50
For 1 inch drive shaft, suitable for tube 50 x 50 mm. Screwing with screw M8x70 (-> not included in delivery package).
 Art.-Nr.: 13a
Ball bearing 55x34
For 1 inch drive shaft, suitable for tube 55x34 mm. Screwing with screw M8 x 70 (-> not included in delivery package).
 Art.-Nr.: 15
Wire tightener
Wire tightener made of galvanized steel, suitable for tube 50x50 mm. Screwing with screw M6x65 (not included in delivery package).
 Art.-Nr.: 17
Drive coil 4.5 m
Semi-shell coil to take up the guiding rope (dia. 3 mm) with a length of up to 4.5 m. Screwing with screw M6x50 (not included in delivery package).
 Art.-Nr.: 17a
Drive coil 7.5 m
Identical half-shell coil as Art.No. 17, but with a cable intake length of 7.5 m. Screwing with screw M6x50 (-> not included in delivery package).
 Art.-Nr.: 17b
Drive coil custom built, full of material
 Art.-Nr.: 18
Drill gauge
Drill gauge for drilling the drive coil 4.5 m.
 Art.-Nr.: 20
Plastic Guide pulley, complete (2 bearing)
 Art.-Nr.: 20a
Plastic guide pulley (2 bearings)
For article Nr. 20.
 Art.-Nr.: 21c
Steel clamp for guide pulleys
 Art.-Nr.: 22
Guide pulley, grey cast iron, galvanized, complete (2 bearings)
A grey cast iron guide pulley, especially developed by Spohr and meeting the requirements of today’s shading systems. The grey cast iron pulley is assembled with 2 bearings and a galvanized steel clamp. This ensures high twisting rigidity and is therefore excellent for installation in long greenhouses.
 Art.-Nr.: 22a
Guide pulley, grey cast iron, galvanized (2 bearings)
 Art.-Nr.: 33a
Universal wire holder, steel 50/50
Very robust holder made of steel, galvanized. Excellent for fastening guide pulleys, stainless steel wire, tighteners etc.
 Art.-Nr.: 35
Glide-off tin plate with 2 rolls
A proven protection for the steel rope at the binder edge.
 Art.-Nr.: 35a
Glide-off tin plate with 1 roll
A proven protection for the steel rope at the binder edge.
 Art.-Nr.: 45
Slider
For fastening the guide tube on the support wires.
 Art.-Nr.: 46
Locking clamp
For fastening the guide tube on the pulling rope.
 Art.-Nr.: 46a
Locking clamp „high“
Extra high locking clamp. It holds the pulling rope approx. 1.5 cm higher, such preventing chating on the binder and the cross ropes.
 Art.-Nr.: 47
Delay clamp
Causes a simple delay of the short fields in conjunction with 2 press sleeves.
 Art.-Nr.: 49
Fabric clamps
For fastening fabrics on the guide tube.
 Art.-Nr.: 50
„Knippie“
Universal clip for fastening fabrics.
 Art.-Nr.: 51
Clamp 25-27/19
To fasten the 19 mm guide tube onto the 25-27 push rods.
 Art.-Nr.: 51a
Clamp 25-27/19 „high“
When using grid binders (Venlo-Block-Construction) the push tube runs over the binder. This clamp prevents the push tube to grind on the binder.
 Art.-Nr.: 51b
Clamp for tube 25-27 mm
 Art.-Nr.: 52
Angle clamp
This angle clamp is applied at the head end of the delay rods.
 Art.-Nr.: 53
Screen closing arm
The back of the fabric is fixed to the arms. The subsequent fabric sheet can overlap the preceeding sheet with its guiding tube by approx. 5 cm and therefore shuts tightly.
 Art.-Nr.: 54
Delay rod complete (3,1 m)
Consists of 19 mm tube of 3,1 m length. Our angle clamp (Art.No.: 52) is fixed at the head end. Additionally our plastic clamp 25-27/19 (Art.No.: 51) is positioned at the other end and is fastened with two hose clamps to set the delay.
 Art.-Nr.: 54a
Delay rod complete (4,1 m)
As Art.No. 54, but with a tube length of 4,1 m.
 Art.-Nr.: 55
Tube joint for 19 mm tube
For the construction of trapezodial systems!
 Art.-Nr.: 56
Tube connector for 19 mm tube
 Art.-Nr.: 57
Guide roll with holder
To guide push rods.
 Art.-Nr.: 57a
Guide roll with holder and binder claw „right“
To guide push rods which run over the binder on the right-hand side.
 Art.-Nr.: 57b
Guide roll with holder and binder claw „left“
To guide push rods which run over the binder on the left-hand side.
 Art.-Nr.: 58
Guide roll
Used with cross ropes for rope- or tube guiding.
 Art.-Nr.: 73
Universal clips
Wind- and weatherproof. Particularly suitable for shading systems outdoors or for the ventilation area of greenhouses. In closed condition the fabric cannot undone even in strong wind.
 Art.-Nr.: 74
Fabric hook
To hang-up the web cloths on the barrow wires.
 Art.-Nr.: 74a
Fabric hook
In reinforced execution.
© by Spohr GmbH 2010 - Impressum